BestPrice Mitutoyo 500-776 Digital Caliper, IP67, LCD, Solar Powered, Metric, 0-150mm Range, +/-0.02mm
The Mitutoyo 500-786 dial caliper measures 0 to 150 mm with +/- 0.01 mm accuracy and is one of Mitutoyo’s Series 500 MyCal Solar Absolute Digimatic Calipers with SPC output. It is made of durable hardened stainless steel and uses Mitutoyo’s ABSOLUTE linear encoder technology. Coolant-proof, it meets IP 67 standards with a dust-tight, waterproof, oilproof, and damage-resistant construction. Its hard-coated solar panels protect the solar cells storing energy for operation. Through solar power, you can measure in any location, including dimly lit areas, without the need to replace batteries.
This digital solar caliper has .295-inch/7.4-mm LCD characters with a five-digit display and easy-to-reach function control buttons. The On/Off button automatically shuts off the caliper after 30 minutes. The solar battery retains its origin point for life (even after the caliper has remained in complete darkness), without requiring the caliper to zero-set its LCD display due to low-light intensity. It uses the inch/metric measuring system.
Although identical to dial and vernier calipers in its ability to make precise measurements, this digital solar caliper also has the LCD, which clearly shows values and increases reading reliability over the other types. The 500-776’s LCD also reflects all ABSOLUTE system activities. The Absolute Scale (ABS) function tracks the origin point—even after shutoff. In environments with available light of 60 Lux or more, the caliper becomes active and you can immediately start measuring, without zero resetting or worrying about overspeed errors. You can make and compare incremental measurements without having to subtract the first measurement from the second.
The 500-776 is IP67 rated for dust, water, and oil protection. It has the ABSOLUTE electromagnetic induction linear encoder and hard-coated solar panels, for increased durability in storing energy in solar cells for safe operation. It weighs approximately 1 lb (453 g) and measures outer diameter (OD), inner diameter (ID), depth, and step, where the butt end of the fixed jaw measures one end of a work piece before its upper/lower or inner/outer "steps" are measured. Outside Jaw Depth is 1.57”/39.87 mm, Inside Jaw Depth is .65”/16.51 mm, Upper Jaw Length is 1.57”/39.87 mm, and Lower Jaw Length is 1.57”/39.87 mm. Range is 0 to 6"/0 to 150 mm, LCD Resolution is .0005"/0.01 mm, Repeatability is .0005"/0.01 mm, and Accuracy is rated + or - 0.001"/0.02 mm. Also included is the on/off automatic shutoff function button. A Digital LCD Data Reading Hold function is available with the optional Data Hold Unit (959143), sold separately. An alarm alerts the user to low voltage and scale contamination and counting value composition errors. A rolling thumb wheel makes fine adjustments and a thumb screw locks the scale’s position. Response speed is unlimited. The caliper has Statistical Process Control (SPC) Data Output capability for manufacturing quality control. It outputs data using a serial data interface to a computer or other dedicated recording device using SPC cable with Data Switch (959149 or 959150, depending on cable length required) or the Mitutoyo U-Wave Wireless Gage Interface (U-WAVE-T, 02AZD730C). The built-in solar cells can store energy for up to three hours of caliper operation. The caliper can be used continuously above 60 Lux (or luminous fLux) ambient illumination.
Calipers measure the distance between two opposing sides of an object. They make inside, outside, depth, or step measurements, according to their type. Calipers are commonly used in architecture, metalworking, mechanical engineering, machining, manufacturing, carpentry, and medicine. The simplest calipers have two legs to mark the two points and require a ruler to take the measurement. More complex calipers use two sets of jaws instead of legs and have up to two graduated scales. Vernier, dial, and digital calipers all give direct and accurate readings and are functionally identical, having a calibrated scale with a fixed jaw and another jaw with a movable pointer that slides along the scale. The vernier caliper has a scale sliding parallel to the main scale for an additional, fractional reading to improve measurement precision. The dial caliper has a circular dial with a pointer on a toothed gear rack replacing the second vernier scale. As with the vernier, this second measurement is added to the reading from the main scale to obtain the result. The dial caliper is used also for measuring size differential between two objects. The digital caliper takes the same sort of differential measurements as the dial caliper by zeroing the display at any point along the slide, with an LCD (replacing the dial) that displays a single, easily read value in both English and metric units. Some digital calipers can hold data readings between measurements and send them to data collection devices.
Founded in Tokyo in 1934, Mitutoyo is a leader in the metrology field, producing high-quality measurement products, including mechanical, dimensional gauging products, focusing on micrometers, calipers, indicators, and other measurement tools, as well as output gauges, interfaces, data collectors, and analysis software. Mitutoyo formed Mitutoyo America Corporation in 1963, which is headquartered in Aurora, Illinois, with additional locations in the U.S. and Canada.
The Mitutoyo 500-776 comes in a fitted, plastic case.
World's unique solar powered super caliper that has no battery The impact resistance of the display unit has been increased for improved usability in workshop conditions IP67 protection assures waterproof reliability This super caliper uses components that do not contain harmful substances and is compatible with RoHS directives Supplied in fitted plastic case Coolant-proof, with IP67 rating, for protection against dust, water, and oil Lightweight, hardened stainless steel construction, for protection of caliper and ABSOLUTE linear encoder technology components Solar-powered, for continuing caliper operation without battery replacement Four-way measurement capability, for multiple applications: outer diameter (OD), inner diameter (ID), depth, and step with SPC output Measure 0 to 150 mm with +/- 0.01 mm accuracyVisit: Discount MailBoss 7207 Package Master Curbside Security Mailbox
ไม่มีความคิดเห็น:
แสดงความคิดเห็น